I built one of these. It is not possible to do so for 60$ anymore since the board itself goes for 150+. On top of that you still need a PSU, NVMe, a high pressure fan, DP to HDMI adapter, possibly BT and Wifi adapters, and a 3d-printed or DIY case.
It is also a very hacky build. You need to flash the BIOS which enables a few interesting unlocks: from 24 to 40 GPU compute units and 6 to 8 CPU cores. It's a bit of a silicon lottery and will depend on your specific board and you need to test everything thoroughly yourself, honing on a config that works for you.
The software side of things is Linux, so if you're familiar with setting it up it shouldn't be difficult to go through the different steps. There are a few distros that work well. I use Bazzite and boot directly to Steam big picture, the UX is great. You can exit to desktop and you have a fully usable Linux box that you can play around with from the comfort of your sofa.
One of the downsides is that it uses a lot of power when idling, about 80W. I just turn it off after using it. I'm working on a QOL feature: an ESP32-based power switch that starts the board when a specific BT device is detected (usually a controller). Once everything is setup the board works very nicely. It can be a bit loud depending on your fan/case combination. I'm currently printing this one[0]
It delivers about the same punch as a standard PS5. The hardware is remarkably similar, and much better than mini PCs set up with AMD APUs, unless you go Strix halo but that is another price league (10x). You can play Cyberpunk 2077 decently on it on settings similar to an AMD RX 6700XT or slightly below RTX 3070.
A pretty impressive number is the memory bandwidth at ~410 GB/s, which should run local LLMs like Gemma 4 or Qwen3.8 27B at decent speed but with limited context size as its just 16Gb
Would I build it again? It was a lot of fun, but financially is not a crazy deal if you need to buy all the materials and factor your time in. Still much cheaper than a Steam Box!
Was it possible to build it for $60 when you built it though?
As for the idle dray, a lot of PC's have Wake On Lan so you can power it on via a special IP packet. I could't get it to work on mine, so i pus an esp32 based power monitoring plug in front of it, and configured the PC to power on directly when powered. When the power monitoring sees the PC sleeping for some time, it cuts the power. I control the plug via home assistant, so i can switch it on remotely
No. I bought it for about 150 shipping included from Canada to Spain. I reckon I spent about 300$ in total, the most expensive thing being the 1Tb NVMe.
I don't have an ethernet cable where the box is, so WoL is not an option for me either. I could have used something similar to your approach (very smart, by the way!) but decided to go ESP aiming for the most console-like experience of just grabbing the controller and playing your game
WoWLAN is a thing. On my motherboard it works so well that it wakes up whenever my phone, laptop or steam deck connect to the WiFi, not just when I actually send the magic packets!
First time I hear about WoWLAN, thanks! I will check if it can work with my cheap usb Wifi adapter.
Yours seems a bit too eager though! I wouldn't want the thing to start up every time I get home as it turns the projector on, which lowers the projector screen, which blocks the (small) apartment's main entrance when lowered and would make me enter home on my fours ¯\_(ツ)_/¯
Hello fellow Spaniard! I just checked the prices and they don't make any sense anymore. A few weeks back you could find the board in Aliexpress for 150eur, now it's twice that price or even more. I got mine fom eBay, didn't think of checking Aliexpress at the time. As per the other parts, I got a quite fancy Metalfish PSU [0] (was on sale when I got it), a power button [1] from Ali (not necessarily needed) and an ESP32 [2] for the remote power on. Then a high pressure fan, I went with Arctic P12 Pro [3]. Wifi and BT adapters whatever works on Linux will work.
I got one for $130 ~8-10 weeks ago. Whew. Lucky. The Steam Machine I think is part of why these things are now suddenly super in demand but also, yeah, it was a riotously good deal for a long time; thank you for this one good thing crypto.
Just to note there are already over a half dozen esp32 based power controllers. The BT detect is cool. Reddit is at the "Yet Another esp32 controller" phase, has been for a while. (I'm not sure if yours is the first or not to do that, I think I've seen similar but maybe it was just yours I saw.) Bless you esp32. Thank you for actually having the obvious good thing, wireless, available for the world (and why did no one else deign do so?)! https://www.reddit.com/r/BC250Gaming/comments/1uylmj0/yet_an...
I don’t see how you could run Qwen3.8 27B on 16GB of memory that’s shared with Linux. Are people running models at 2bit quants? Are they even worth bothering with? I had assumed you go down to 4bit and if you need to go smaller you have to lose parameters.
You can, it's kind of cool to have this capability on something gaming at such a low price tag. Its not optimal for your time but beats nothing by a LOT. And that model is pretty reliable.
In my particular case the HDMI goes directly into a sound bar which does not have a DP input. I assume most people building a box like this will connect it to a TV, which is most commonly HDMI-only. So technically not a strong requirement but practically almost
I bought one while waiting to see if my Steam Machine reservation would be fulfilled.
I paid ~$186 shipped for the board on eBay 5 weeks ago. I use an ATX power supply and NVMe that I had laying around and I printed a big case for it[0].
I seem to have gotten a good one as it has no problems after unlocking the extra CPU/GPU cores.
I run vanilla Arch on mine configured to boot into Steam. The jank factor is pretty high but it does trade blows with the Steam Machine for a fraction of the price.[1]
I did end up going through with the purchase of a 512GB Steam Machine for $1160 w/tax and swapped in a 2TB NVMe. It is definitely a more polished/living room-ready product and I'm happy with the hardware but it's definitely a questionable value.
It's worth reading over the docs[2] first before committing. There are lots of options for cooling, storage, and power supplies. Just depends on what you want to get out of it and how much time you want to invest in it. There are pre-made images so you don't necessarily need to be a Linux expert but it would help if you want to stay on top of the latest developments. There is still on-going work to get even more performance[3]
I think we will continue to see some performance improvements for both systems over the next coming months.
It works great if you turn the BC-250 on, play games, and turn it off.
By jank, I mean it's not a streamlined console experience like the Steam Machine. There's no suspend/resume and the idle power is quite high. If you want wifi/bluetooth, you'll have to pick a chipset well supported by Linux. (I use ethernet and a steam controller). If you want USB ports and a power button in the front like a console would have, you'll have to pick a solution for those. Carefully read over the options for power and cooling. They're very important if you're going for max performance. All the little extras add to the over-all cost as well.
https://mosfet.party/ sells a bunch of BC-250 add-ons to give you an idea of price and options.
You are _not_ getting one of these for less than $300, and because of this post and many like it, there are countless scams selling just cases for them at this price from a dollar or two of filament.
This always makes me ambivalent about enthusiast blog posts. Like on the one hand, cool that the knowledge gets spread. On the other hand, whenever one gets popular, another hidden gem skyrockets in price or becomes semi-permanently low in stock.
If it's advertised as a case and it works, why is it a scam? I don't own a 3D printer, nor do I know anyone who does. If someone is designing, printing, and selling a useful product, why is that a scam?
If you are selling a product for way more than it should cost (like a $60 3D printed case), when that cost is the exact price that a popular blog says the computer costs, you are intentionally hoping to prey on people mistaking your listing for the actual computer.
You can make all sorts of arguments about possible reasons for charging that exact price for that exact product, but no reasonable person is going to buy that.
I think they are saying people mislead customers into thinking they are getting a "$60 gaming pc" when they are actually just getting a 3d printed case with nothing inside.
Because the sellers are categorizing them as computers on ebay and filling in all of the appropriate specifications as if it was the computer, and only putting in the description "CASE ONLY, DOES NOT INCLUDE ANY COMPUTER PARTS".
Automatically no 3d printed case is worth $300 because it's not possible to make it good enough quality.
A metal and wood case could be worth $300.
A good design is worth something, and a good printing job is worth something, and the convenience of a service is worth something, but no amount of good design and quality printing job and service convenience can make a 3d printed case worth more than about $50 before shipping, and it would need to be somehow pretty special design to overcome some basic material and process weaknesses and still be functional and look good to be worth that much.
$300 is too high, but $50 is too low. 3D print sellers aren't doing injection molded parts at scale, nor offshoring the labor. For GP's linked case file; between the filament, the compatible linked switch and fan hardware not purchased by the thousands, and someone paying themself at least minimum wage to print all 46 individual parts and then to partially assemble and package it up nicely (and not counting printer hardware depreciation or electricity), $50 for it is not a viable product to sell or to run as a business. That's the price I would budget for making it myself with the 3D printer I already own and not counting my time as a cost, not something I would waste my time with selling.
$60 gaming PC's are doable if you buy an "untested" Dell Optiplex and get lucky. A few years ago, I bought a couple of these in that price range that not only worked, but had a GPU of some kind. Good enough for Left4Dead at least, and some other Indie games. All they needed was an HDD with Windows 10 (both of which I had lying around - Win10 licenses can be had for a few bucks).
There's a similar board called the AMD 4800S (or 4700S). These are also repurposed PS5 SoC that didn't pass the graphics quality control. So what you get is a motherboard with CPU and 16GB RAM soldered on. No HDMI out, but it has a 16x PCIe slot (PCIe 4x 4.0) to connect a graphics card. The 4700S model is limited to 4x PCIe 2.0.
I checked it out and total cost is too high compared to what you get in modern Mini PCs. Also, the 4800S is difficult to get and 4700S supports only SATA SSDs.
Yeah the prices were much lower last year, but I think this is still a good deal for the tinkerers.
I've just added the how to portion of the CU 32->40 unlock on Manjaro Linux. Plus added an AGENTS.md so you can use your favorite AI to guide you trough the full process.
Sure it's noise but it does serve a valuable purpose so I don't waste my limited time reading an article on the front page if I see a consensus from dozens of AI complaints in the comments.
Dang at one point mentioned HN was planning to create another flag button specifically for obviously AI written content which would be the best solution IMO. If implemented then trivial AI complaints could be considered spam and told to use the AI flag instead.
Readers could then decide themselves if they want to click through after seeing some kind of small AI indicator next to the post when the flags pass some threshold, at least that's how imagined it could work for posts.
I’m not sure about that. I suspect we are getting a lot of false positives. Several times the author of an article has joined the conversation and vehemently denied using AI.
Ultimately the post appears here because it is getting upvotes. If people didn’t want it then they wouldn’t upvote it.
I have a bunch of these as headless gaming PCs in a rack running sunshine and Steam on Linux. The kids stream from them using moonlight on whatever smart device they want to play on.
Had the idea from LTT but he went a bit bonkers and bought expensive hardware to transmit video and input over cables. Gigabit Ethernet is more than enough.
We are able to make do with Software Encoding for now, more so with the unlocked cores but it is limiting its potential. There seems to be something called PyroWave making waves for being a low latency encoder/ decoder but nothing supports it yet except for a now pulled Steam Beta.
Otherwise I'll have to investigate capturing video via the DP port or switch it out altogether.
This isn't necessary related to this project but I got thinking about while reading it. Isn't it weird that shared memory was a cost saving measure by not having GPU dedicated has now been rechristened unified memory and is now a feature?
I understand why the AI people want it to help with the latency between the CPU and GPU. But having people in some cases use it as for marketing is kinda like getting watered down beer and getting told its a good thing because alcohol is bad for you.
Technically, “unified memory” is where both the GPU and CPU have access to the RAM over the same bus, which is different from the older, reviled “shared memory”, where the RAM was always at least one bus hop away from the GPU. But yes, there is a certain amount of spin to it, isn't there? (“You have less total memory now, and that's a Good Thing!”)
> I understand why the AI people want it to help with the latency between the CPU and GPU.
The reason AI users like it is because it provides a large amount of higher-bandwidth memory at a price much lower than an equivalent GPU.
If you had 16GB of DDR5 in a normal 2-channel consumer board it would not be this fast.
This gives 16GB of high speed memory for a very low price compared to a full GPU.
The larger unified memory systems like Strix Halo or Apple Silicon provide access to high bandwidth memory at scales you can’t get with any consumer GPU.
> But having people in some cases use it as for marketing is kinda like getting watered down beer and getting told its a good thing because alcohol is bad for you
I don’t think you understand the benefits of having high speed memory attached at a low price point.
Yes we would all prefer to have the same amount of even faster memory attached to a dedicated GPU, but that’s not happening at this price point.
Better analogy would be that this is an entry-level sports car for the price of a Honda Civic but you’re complaining that it’s not a Lamborghini.
> The reason AI users like it is because it provides a large amount of higher-bandwidth memory at a price much lower than an equivalent GPU.
But unified memory isn't providing high bandwidth. Apple's specific implementation on pro or higher chips does. There's a zillion desktops and laptops running unified memory at low to medium-low speeds, and the baseline M series is part of that with its 128 bit bus.
Most unified memory devices are handicapped because of the unification, not boosted. Yet people keep praising unified memory.
Primarily the bottleneck actually. PCIe bandwidth is extremely limited.
GDDR has worse latency than DDR and scaling it up to larger capacities faces challenges. So if you unify memory your options are small GDDR, large DDR, or expensive HBM.
Unusually, the BC-250 and PS5 both use GDDR with the CPU so the memory bandwidth is great but the latency not so much AFAIK. It's like using a dGPU as a full computer.
It’s an intriguing machine, but, by now, I’d have imagined someone would offer a sheet metal case with a PSU and fan (or mounting holes, at least).
The form factor is unfortunate. I wonder what was the intended usage (server side gaming?) and if other high-volume parts (as game console APUs are) can become small similar systems, preferably with expandable memory). The history of how this thing came into being must be really interesting.
Speaking of form factors, it’s a shame there is no generic desktop/deskside/tower conversion kit for 4 and 5u rack servers. Some machines have tower counterparts, but having an aftermarket option would save a lot of machines from the metal crushers.
If one were to actually build and design a SoC, ARM $60 game “console” that plugs into your TV in 2026 and sell it at a decent volume, what would the equivalent game console be potential-wise?
I’ve been doing 3D game development for retro consoles for fun and it’s actually quite impressive what you can actually achieve with little hardware.
The Switch is essentially that. Obviously not $60 but it's a several generations old Nvidia Tegra SoC. The AppleTV wasn't far off either before its massive price hikes.
Not $60, but a bit close. I'd do something based on the RK3588 SoC. It's pretty beefy. GPU isn't stellar but it does have good video codec, a proper PCIe bus including support for e.g. m.2 slot nVME on many boards, and decent amounts of RAM, and good a multicore basis.
And there's some amount of kernel upstreaming that makes it a bit friendlier than some.
You hang out on weird hardware hacker forums and spot what people are working on. You can try buying the things multiple people are working on and getting good early results on. But most of it will end up being ewaste.
I actually got very interested in this sort of hardware repurposing, if someone know of any kind of place where people discuss and keep track of this, please share!
Cloud gaming is incredible tech, I used GFN for a while and it was incredible.
HOWEVER, I will inevitably want to play weird stuff like "milk inside a bag of milk inside a bag of milk", Pseudoregalia or Civ V Lekmod, which these cloud services do not offer.
The other alternative is "rent a VM" systems like Shadow Gaming, but they're much more expensive, and have much worse latency and streaming tech. Also the questionable practice of putting the credentials for my precious steam account in a random VM in some random data center.
"many PS5 APUs that didn’t meet console spec (“binned” or “defective” for console use) got repurposed. Instead of being discarded, these chips were re-used for mining/higher-density hardware."
Not discussed much in the article, but it looks like:
TSMC → AMD controlled/qualified the usable off-spec parts → AMD supplied BC-250 parts to ASRock → ASRock sold mining hardware.
No graphics output. And so loud you wouldn’t be able to hear your game either. Also they use about 1kw of power, so you’d only want to run it in the winter.
You can get them that cheap, you just need a time machine. I built a few that were about that price including a free 128GB SSD in late 2024. The FSP500 PSU from one particular ebay seller was cheaper then too ($5-10).
Been really fun watching this go from e-waste to having mesa support and CU/CPU unlocks.
I built one of these. It is not possible to do so for 60$ anymore since the board itself goes for 150+. On top of that you still need a PSU, NVMe, a high pressure fan, DP to HDMI adapter, possibly BT and Wifi adapters, and a 3d-printed or DIY case.
It is also a very hacky build. You need to flash the BIOS which enables a few interesting unlocks: from 24 to 40 GPU compute units and 6 to 8 CPU cores. It's a bit of a silicon lottery and will depend on your specific board and you need to test everything thoroughly yourself, honing on a config that works for you.
The software side of things is Linux, so if you're familiar with setting it up it shouldn't be difficult to go through the different steps. There are a few distros that work well. I use Bazzite and boot directly to Steam big picture, the UX is great. You can exit to desktop and you have a fully usable Linux box that you can play around with from the comfort of your sofa.
One of the downsides is that it uses a lot of power when idling, about 80W. I just turn it off after using it. I'm working on a QOL feature: an ESP32-based power switch that starts the board when a specific BT device is detected (usually a controller). Once everything is setup the board works very nicely. It can be a bit loud depending on your fan/case combination. I'm currently printing this one[0]
It delivers about the same punch as a standard PS5. The hardware is remarkably similar, and much better than mini PCs set up with AMD APUs, unless you go Strix halo but that is another price league (10x). You can play Cyberpunk 2077 decently on it on settings similar to an AMD RX 6700XT or slightly below RTX 3070.
A pretty impressive number is the memory bandwidth at ~410 GB/s, which should run local LLMs like Gemma 4 or Qwen3.8 27B at decent speed but with limited context size as its just 16Gb
Would I build it again? It was a lot of fun, but financially is not a crazy deal if you need to buy all the materials and factor your time in. Still much cheaper than a Steam Box!
- [0] https://makerworld.com/en/models/3021754-bc250-case-mkuu-fsp...
Edit: GPU performance comparison
Was it possible to build it for $60 when you built it though?
As for the idle dray, a lot of PC's have Wake On Lan so you can power it on via a special IP packet. I could't get it to work on mine, so i pus an esp32 based power monitoring plug in front of it, and configured the PC to power on directly when powered. When the power monitoring sees the PC sleeping for some time, it cuts the power. I control the plug via home assistant, so i can switch it on remotely
No. I bought it for about 150 shipping included from Canada to Spain. I reckon I spent about 300$ in total, the most expensive thing being the 1Tb NVMe.
I don't have an ethernet cable where the box is, so WoL is not an option for me either. I could have used something similar to your approach (very smart, by the way!) but decided to go ESP aiming for the most console-like experience of just grabbing the controller and playing your game
WoWLAN is a thing. On my motherboard it works so well that it wakes up whenever my phone, laptop or steam deck connect to the WiFi, not just when I actually send the magic packets!
First time I hear about WoWLAN, thanks! I will check if it can work with my cheap usb Wifi adapter.
Yours seems a bit too eager though! I wouldn't want the thing to start up every time I get home as it turns the projector on, which lowers the projector screen, which blocks the (small) apartment's main entrance when lowered and would make me enter home on my fours ¯\_(ツ)_/¯
On the other hand if you re-arranged the room, it'd be neat to walk in to everything deploying!
Would you mind to share here or by DM where you ordered items from? I’m in Spain and would like to build something similar.
Thanks
Hello fellow Spaniard! I just checked the prices and they don't make any sense anymore. A few weeks back you could find the board in Aliexpress for 150eur, now it's twice that price or even more. I got mine fom eBay, didn't think of checking Aliexpress at the time. As per the other parts, I got a quite fancy Metalfish PSU [0] (was on sale when I got it), a power button [1] from Ali (not necessarily needed) and an ESP32 [2] for the remote power on. Then a high pressure fan, I went with Arctic P12 Pro [3]. Wifi and BT adapters whatever works on Linux will work.
[0] https://es.aliexpress.com/item/1005009609601844.html
[1] https://es.aliexpress.com/item/1005011847734240.html
[2] https://es.aliexpress.com/item/1005007479144456.html
[3] https://www.amazon.es/dp/B0DJDC74BP?th=1
Ouch! Thank you for checking it! It’s always nice to find Spanish people here :D
Are there DP-HDMI adapters that work with HD audio bitstreaming and VRR? Different use case, but I've not had much luck finding good options.
I got one for $130 ~8-10 weeks ago. Whew. Lucky. The Steam Machine I think is part of why these things are now suddenly super in demand but also, yeah, it was a riotously good deal for a long time; thank you for this one good thing crypto.
Just to note there are already over a half dozen esp32 based power controllers. The BT detect is cool. Reddit is at the "Yet Another esp32 controller" phase, has been for a while. (I'm not sure if yours is the first or not to do that, I think I've seen similar but maybe it was just yours I saw.) Bless you esp32. Thank you for actually having the obvious good thing, wireless, available for the world (and why did no one else deign do so?)! https://www.reddit.com/r/BC250Gaming/comments/1uylmj0/yet_an...
Well played! I guess we’ll never see such prices anymore.
With regards to the wireless power on, I was definitely not the trail blazer. I’m just using https://github.com/Thunkar/bc250-esp32-switch
I don’t see how you could run Qwen3.8 27B on 16GB of memory that’s shared with Linux. Are people running models at 2bit quants? Are they even worth bothering with? I had assumed you go down to 4bit and if you need to go smaller you have to lose parameters.
You can, it's kind of cool to have this capability on something gaming at such a low price tag. Its not optimal for your time but beats nothing by a LOT. And that model is pretty reliable.
https://unsloth.ai/docs/basics/dynamic-3.0-ggufs
> you still need ... DP to HDMI adapter
what for? just use DP
In my particular case the HDMI goes directly into a sound bar which does not have a DP input. I assume most people building a box like this will connect it to a TV, which is most commonly HDMI-only. So technically not a strong requirement but practically almost
My monitor doesn't have a DisplayPort port.
I bought one while waiting to see if my Steam Machine reservation would be fulfilled.
I paid ~$186 shipped for the board on eBay 5 weeks ago. I use an ATX power supply and NVMe that I had laying around and I printed a big case for it[0].
I seem to have gotten a good one as it has no problems after unlocking the extra CPU/GPU cores.
I run vanilla Arch on mine configured to boot into Steam. The jank factor is pretty high but it does trade blows with the Steam Machine for a fraction of the price.[1]
I did end up going through with the purchase of a 512GB Steam Machine for $1160 w/tax and swapped in a 2TB NVMe. It is definitely a more polished/living room-ready product and I'm happy with the hardware but it's definitely a questionable value.
It's worth reading over the docs[2] first before committing. There are lots of options for cooling, storage, and power supplies. Just depends on what you want to get out of it and how much time you want to invest in it. There are pre-made images so you don't necessarily need to be a Linux expert but it would help if you want to stay on top of the latest developments. There is still on-going work to get even more performance[3]
- [0] https://www.printables.com/model/1789618-bc-250-atx-case-dua...
- [1] https://www.youtube.com/watch?v=5Sw1SdU9buQ
- [2] https://elektricm.github.io/amd-bc250-docs/
- [3] https://github.com/lonewolf0622/BC250-Native-Mesh-Shaders-
What's the performance delta? I'm waiting on a SM reservation but I wouldn't mind saving $500+ :)
Is there any "jank" during active use or is this mostly a set up thing?
They are very close in benchmarks. https://i.imgur.com/Bk5Dcfb.jpeg
I think we will continue to see some performance improvements for both systems over the next coming months.
It works great if you turn the BC-250 on, play games, and turn it off.
By jank, I mean it's not a streamlined console experience like the Steam Machine. There's no suspend/resume and the idle power is quite high. If you want wifi/bluetooth, you'll have to pick a chipset well supported by Linux. (I use ethernet and a steam controller). If you want USB ports and a power button in the front like a console would have, you'll have to pick a solution for those. Carefully read over the options for power and cooling. They're very important if you're going for max performance. All the little extras add to the over-all cost as well.
https://mosfet.party/ sells a bunch of BC-250 add-ons to give you an idea of price and options.
You are _not_ getting one of these for less than $300, and because of this post and many like it, there are countless scams selling just cases for them at this price from a dollar or two of filament.
This always makes me ambivalent about enthusiast blog posts. Like on the one hand, cool that the knowledge gets spread. On the other hand, whenever one gets popular, another hidden gem skyrockets in price or becomes semi-permanently low in stock.
The invisible hand of the market finger-blasting our wallets again.
If it's advertised as a case and it works, why is it a scam? I don't own a 3D printer, nor do I know anyone who does. If someone is designing, printing, and selling a useful product, why is that a scam?
If you are selling a product for way more than it should cost (like a $60 3D printed case), when that cost is the exact price that a popular blog says the computer costs, you are intentionally hoping to prey on people mistaking your listing for the actual computer.
You can make all sorts of arguments about possible reasons for charging that exact price for that exact product, but no reasonable person is going to buy that.
I think they are saying people mislead customers into thinking they are getting a "$60 gaming pc" when they are actually just getting a 3d printed case with nothing inside.
Because the sellers are categorizing them as computers on ebay and filling in all of the appropriate specifications as if it was the computer, and only putting in the description "CASE ONLY, DOES NOT INCLUDE ANY COMPUTER PARTS".
Automatically no 3d printed case is worth $300 because it's not possible to make it good enough quality.
A metal and wood case could be worth $300.
A good design is worth something, and a good printing job is worth something, and the convenience of a service is worth something, but no amount of good design and quality printing job and service convenience can make a 3d printed case worth more than about $50 before shipping, and it would need to be somehow pretty special design to overcome some basic material and process weaknesses and still be functional and look good to be worth that much.
$300 is too high, but $50 is too low. 3D print sellers aren't doing injection molded parts at scale, nor offshoring the labor. For GP's linked case file; between the filament, the compatible linked switch and fan hardware not purchased by the thousands, and someone paying themself at least minimum wage to print all 46 individual parts and then to partially assemble and package it up nicely (and not counting printer hardware depreciation or electricity), $50 for it is not a viable product to sell or to run as a business. That's the price I would budget for making it myself with the 3D printer I already own and not counting my time as a cost, not something I would waste my time with selling.
Fair
The cases are $60, the "original" price, not $300. Search ebay for BC-250, they're everywhere.
Agreed a $60 case, even if 3d printed as long as it's good, is no scam.
How is it a scam to sell something for more than the cost to make it? Labor and energy are not free you know.
I've got a bridge to sell you
$60 gaming PC's are doable if you buy an "untested" Dell Optiplex and get lucky. A few years ago, I bought a couple of these in that price range that not only worked, but had a GPU of some kind. Good enough for Left4Dead at least, and some other Indie games. All they needed was an HDD with Windows 10 (both of which I had lying around - Win10 licenses can be had for a few bucks).
As long as you only want to play games from 2008. :)
I'm in!
> $60 gaming PC's are doable if you buy an "untested" Dell Optiplex and get lucky.
Yeah, but a $60 lottery ticket that pays off in an X if you win isn’t a $60 X.
I'd take these over a lottery ticket. Not mentioned: I'd bought a handful of these off CL as well, and they all worked.
Dell business machines are pretty reliable. It's a much better wager than a lotto ticket.
https://web.archive.org/web/20260707135659/https://devquasar...
For anyone wondering about local LLM applications:
- current price $200+
- limited VRAM (12-14 GB)
- poor performamce in clusters [1] - only 2 lanes of PCI-e 2.0 (still better than CMP XX HX mining cards)
[1] https://ciroluciotecce.it/en/posts/bc250-cluster-inferenza-l...
There's a similar board called the AMD 4800S (or 4700S). These are also repurposed PS5 SoC that didn't pass the graphics quality control. So what you get is a motherboard with CPU and 16GB RAM soldered on. No HDMI out, but it has a 16x PCIe slot (PCIe 4x 4.0) to connect a graphics card. The 4700S model is limited to 4x PCIe 2.0.
I checked it out and total cost is too high compared to what you get in modern Mini PCs. Also, the 4800S is difficult to get and 4700S supports only SATA SSDs.
Here's the GitHub repository linked by the (currently unreachable) article in the OP:
https://github.com/csabakecskemeti/amd_bc-250_how-to
Hey all! I've wrote the original [blogpost](https://devquasar.com/hardware/the-60-gaming-pc-amd-bc-250/) last year and maintaining the [how-to](https://github.com/csabakecskemeti/amd_bc-250_how-to) repo. I'm glad you found it useful!
Yeah the prices were much lower last year, but I think this is still a good deal for the tinkerers.
I've just added the how to portion of the CU 32->40 unlock on Manjaro Linux. Plus added an AGENTS.md so you can use your favorite AI to guide you trough the full process.
Happy hacking!
Does anyone else immediately lose interest in an article when you realize it was written by AI?
Yes but I'm also getting a bit tired of reading complaints about it as well.
Sure it's noise but it does serve a valuable purpose so I don't waste my limited time reading an article on the front page if I see a consensus from dozens of AI complaints in the comments.
Dang at one point mentioned HN was planning to create another flag button specifically for obviously AI written content which would be the best solution IMO. If implemented then trivial AI complaints could be considered spam and told to use the AI flag instead.
Readers could then decide themselves if they want to click through after seeing some kind of small AI indicator next to the post when the flags pass some threshold, at least that's how imagined it could work for posts.
I’m not sure about that. I suspect we are getting a lot of false positives. Several times the author of an article has joined the conversation and vehemently denied using AI.
Ultimately the post appears here because it is getting upvotes. If people didn’t want it then they wouldn’t upvote it.
i would happily use my pangram plan to submit report pdfs
That would be a good solution. I'd very much like that.
I'm just tired.
Is it? Pangram disagrees and human-made photos imply at least some human effort.
I have a bunch of these as headless gaming PCs in a rack running sunshine and Steam on Linux. The kids stream from them using moonlight on whatever smart device they want to play on.
Had the idea from LTT but he went a bit bonkers and bought expensive hardware to transmit video and input over cables. Gigabit Ethernet is more than enough.
Is that just with software encoding? Or did hardware encoding get fixed?
We are able to make do with Software Encoding for now, more so with the unlocked cores but it is limiting its potential. There seems to be something called PyroWave making waves for being a low latency encoder/ decoder but nothing supports it yet except for a now pulled Steam Beta.
Otherwise I'll have to investigate capturing video via the DP port or switch it out altogether.
I wish I had learned about this when it was still $60. In Canada I can't find any for less than $300.
These are going for a few hundred dollars now due to demand.
This isn't necessary related to this project but I got thinking about while reading it. Isn't it weird that shared memory was a cost saving measure by not having GPU dedicated has now been rechristened unified memory and is now a feature?
I understand why the AI people want it to help with the latency between the CPU and GPU. But having people in some cases use it as for marketing is kinda like getting watered down beer and getting told its a good thing because alcohol is bad for you.
Technically, “unified memory” is where both the GPU and CPU have access to the RAM over the same bus, which is different from the older, reviled “shared memory”, where the RAM was always at least one bus hop away from the GPU. But yes, there is a certain amount of spin to it, isn't there? (“You have less total memory now, and that's a Good Thing!”)
> I understand why the AI people want it to help with the latency between the CPU and GPU.
The reason AI users like it is because it provides a large amount of higher-bandwidth memory at a price much lower than an equivalent GPU.
If you had 16GB of DDR5 in a normal 2-channel consumer board it would not be this fast.
This gives 16GB of high speed memory for a very low price compared to a full GPU.
The larger unified memory systems like Strix Halo or Apple Silicon provide access to high bandwidth memory at scales you can’t get with any consumer GPU.
> But having people in some cases use it as for marketing is kinda like getting watered down beer and getting told its a good thing because alcohol is bad for you
I don’t think you understand the benefits of having high speed memory attached at a low price point.
Yes we would all prefer to have the same amount of even faster memory attached to a dedicated GPU, but that’s not happening at this price point.
Better analogy would be that this is an entry-level sports car for the price of a Honda Civic but you’re complaining that it’s not a Lamborghini.
> The reason AI users like it is because it provides a large amount of higher-bandwidth memory at a price much lower than an equivalent GPU.
But unified memory isn't providing high bandwidth. Apple's specific implementation on pro or higher chips does. There's a zillion desktops and laptops running unified memory at low to medium-low speeds, and the baseline M series is part of that with its 128 bit bus.
Most unified memory devices are handicapped because of the unification, not boosted. Yet people keep praising unified memory.
> want it to help with the latency
Primarily the bottleneck actually. PCIe bandwidth is extremely limited.
GDDR has worse latency than DDR and scaling it up to larger capacities faces challenges. So if you unify memory your options are small GDDR, large DDR, or expensive HBM.
Unusually, the BC-250 and PS5 both use GDDR with the CPU so the memory bandwidth is great but the latency not so much AFAIK. It's like using a dGPU as a full computer.
It’s an intriguing machine, but, by now, I’d have imagined someone would offer a sheet metal case with a PSU and fan (or mounting holes, at least).
The form factor is unfortunate. I wonder what was the intended usage (server side gaming?) and if other high-volume parts (as game console APUs are) can become small similar systems, preferably with expandable memory). The history of how this thing came into being must be really interesting.
Speaking of form factors, it’s a shame there is no generic desktop/deskside/tower conversion kit for 4 and 5u rack servers. Some machines have tower counterparts, but having an aftermarket option would save a lot of machines from the metal crushers.
The intended usage was crypto mining. You bought a 4U of these in a rack of 12 blades.
The link died, but it's a cut-down PS5 APU previously sold for crypto mining apparently.
Not so cut down - you can unlock more GPU and CPU cores (some of them might be broken).
Not cut-down and yes... i deployed 20,000 of them for crypto mining... optimized around ~54mhs on ethash which was pretty good.
If one were to actually build and design a SoC, ARM $60 game “console” that plugs into your TV in 2026 and sell it at a decent volume, what would the equivalent game console be potential-wise?
I’ve been doing 3D game development for retro consoles for fun and it’s actually quite impressive what you can actually achieve with little hardware.
The Switch is essentially that. Obviously not $60 but it's a several generations old Nvidia Tegra SoC. The AppleTV wasn't far off either before its massive price hikes.
Not $60, but a bit close. I'd do something based on the RK3588 SoC. It's pretty beefy. GPU isn't stellar but it does have good video codec, a proper PCIe bus including support for e.g. m.2 slot nVME on many boards, and decent amounts of RAM, and good a multicore basis.
And there's some amount of kernel upstreaming that makes it a bit friendlier than some.
I couldn’t find a board under $120, but this would be a compelling target performance wise, even with 4GB shared memory
the silicon lottery in reverse: ps5 chips that failed console binning now power cyberpunk 2077 rigs for ~$70. best e-waste redemption arc in a while.
How could I have found out about these machines months ago before the price went up? Where do I have to browse and connect around?
You hang out on weird hardware hacker forums and spot what people are working on. You can try buying the things multiple people are working on and getting good early results on. But most of it will end up being ewaste.
Is this the only piece of hardware that can be repurposed like this or are there other crypto mining (or AI?…) devices that have similar potential?
I actually got very interested in this sort of hardware repurposing, if someone know of any kind of place where people discuss and keep track of this, please share!
There were cheap nvidia crypto GPU's based on the A100 that recently got unlocked. They are no longer cheap.
Is there anything similar/newer that’s still a good deal?
Where are you all finding these for sale? I couldn’t find anything other than “kits” or on eBay for $400
Linus Tech Tips dropped a video on this an hour ago, so the prices are already skyrocketing sadly.
Link: https://youtu.be/lmLh29LE2W4?is=QdRwtQS3xyyPt44E
Yuck... They increased a bit ($150+?) after the GPU unlock came out, but they're nuts now.
some info links:
- https://github.com/mothenjoyer69/bc250-documentation
- https://gitlab.com/TuxThePenguin0/bc250-bios
- https://bc250.info/
Some of the smaller llm models run on it too but in practice the memory is way too limited for that use case.
Love these articles. Need a little more cash, a little more time. A little drop in ram prices...
I looked into a bunch of things like this, but in the end I decided to just pay for a Boosteroid subscription (cloud gaming service). Works great.
Cloud gaming is incredible tech, I used GFN for a while and it was incredible.
HOWEVER, I will inevitably want to play weird stuff like "milk inside a bag of milk inside a bag of milk", Pseudoregalia or Civ V Lekmod, which these cloud services do not offer.
The other alternative is "rent a VM" systems like Shadow Gaming, but they're much more expensive, and have much worse latency and streaming tech. Also the questionable practice of putting the credentials for my precious steam account in a random VM in some random data center.
"many PS5 APUs that didn’t meet console spec (“binned” or “defective” for console use) got repurposed. Instead of being discarded, these chips were re-used for mining/higher-density hardware."
Not discussed much in the article, but it looks like:
TSMC → AMD controlled/qualified the usable off-spec parts → AMD supplied BC-250 parts to ASRock → ASRock sold mining hardware.
Much like the website, it's unavailable.
Wake me up when you can buy this for $60 again. Maybe in 2035
> The Linux version of Steam works out of the box.
So, essentially a decent Steam Link remote play server.
So this is the future of the Nvidia B200 cards as well
No graphics output. And so loud you wouldn’t be able to hear your game either. Also they use about 1kw of power, so you’d only want to run it in the winter.
What Nvidia B200 Cards?
Site (Wordpress) seems to have gotten the HN kiss of death
This is the guide you need. I run one of these. https://elektricm.github.io/amd-bc250-docs/
> Ok it’s not exactly $60 but you can get the board itself for that amount of money on eBay if you’re lucky
I guffawed. And then closed the tab.
You can get them that cheap, you just need a time machine. I built a few that were about that price including a free 128GB SSD in late 2024. The FSP500 PSU from one particular ebay seller was cheaper then too ($5-10).
Been really fun watching this go from e-waste to having mesa support and CU/CPU unlocks.
Also no display? What kind of games are we playing
It's got display port.